管中泵的检修及检修方法

管中泵的检修及检修方法
维护保养将延长管道中泵的使用寿命。维修方面，龙亚泵业的编辑将为您介绍。
（1） 检查泵、管路及不锈钢管接头是否松动。
（2） 向轴承体中加入轴承润滑油，观察油痕中心线油位，及时更换或补充润滑油。
（3） 如果不锈钢管中泵长时间停用，应将泵完全拆开，将水吹干，转动部件和接头涂上润滑脂，安装并妥善保管。
（4） 关闭出口管道闸阀、出口压力表、JK真空表。
（5） 点动电机，查看电机转向是否正确。
（6） 启动电机。当不锈钢管中泵正常运行时，打开出口压力表和JK真空泵。根据适当的压力逐渐打开闸阀，检查电机负载。
（7） 尽量将不锈钢泵的流量和扬程控制在标牌上标明的范围内，使不锈钢管中泵能在高效率点运行，从而达到节能的效果。欢迎参考更多相关介绍喷泉专用泵型号参数（8）不锈钢管中泵运行时，轴承温度不应超过环境温度35C，温度不应超过80C。
（9）如果VAREM不锈钢管中泵有异响，立即停止泵并检查原因。
（10） 当不锈钢管中泵要停止时，先关闭闸阀和压力表，然后停止电机。
（11） 不锈钢管中泵在每个月100小时后更换润滑油，然后每500小时更换一次润滑油。
（12） 填料压盖应经常调整，填料室内滴漏应正常。
（13） 定期检查轴套磨损情况，磨损较大时及时更换。
（14） 不锈钢管中泵在寒冷的冬季使用时，停车后需将泵体吊离水面，无需防水，防止冻裂。以上是关于WATERSUNNY管中泵的维护保养方法，通过合理的维护保养，不仅可以及时发现存在的问题，而且可以使管中泵的使用寿命更长。ZILMET管中泵具有噪音低、无污染、体积小、节省空间、安装配套水平高、产品质量优良、服务全面等特点，值得客户选择。上海龙亚泵业还专注于ZILMET管中泵、潜水电机、供水管中泵组的生产制造。欢迎咨询！

Maintenance of pump in pipe and maintenance methods
Maintenance will extend the service life of the pump in the pipeline. In terms of maintenance, the editor of Longya pump will introduce it to you.
(1) Check whether the pump, pipeline and stainless steel pipe joint are loose.
(2) Add bearing lubricating oil to the bearing body, observe the oil level of the oil mark center line, and replace or supplement the lubricating oil in time.
(3) If the pump in stainless steel pipe is out of service for a long time, the pump should be completely disassembled, the water should be blown dry, the rotating parts and joints should be coated with grease, installed and properly kept.
(4) Close the outlet pipe gate valve, outlet pressure gauge and JK vacuum gauge.
(5) Jog the motor to check whether the motor steering is correct.
(6) Start the motor. When the pump in stainless steel pipe runs normally, open the outlet pressure gauge and JK vacuum pump. Gradually open the gate valve according to the appropriate pressure and check the motor load.
(7) Try to control the flow and lift of the stainless steel pump within the range indicated on the label, so that the pump in the stainless steel pipe can operate at the high efficiency point, so as to achieve the effect of energy saving. Welcome to refer to more relevant introduction fountain special pump model parameters (8) when the stainless steel pipe pump is running, the bearing temperature should not exceed the ambient temperature of 35C, the temperature should not exceed 80C.
(9) If the pump in the varem stainless steel pipe has abnormal noise, stop the pump immediately and check the cause.
(10) When the stainless steel pipe pump to stop, first close the gate valve and pressure gauge, and then stop the motor.
(11) The lubricating oil of stainless steel tube pump is changed after 100 hours every month, and then every 500 hours.
(12) The packing gland should be adjusted frequently, and the leakage in the packing chamber should be normal.
(13) Regularly check the wear of the shaft sleeve, and replace it in time when the wear is large.
(14) When the pump in stainless steel pipe is used in cold winter, it is necessary to lift the pump body away from the water surface after parking, so there is no need to waterproof and prevent frost cracking. The above is about the maintenance method of watersunny in pipe pump. Through reasonable maintenance, not only the existing problems can be found in time, but also the service life of in pipe pump can be longer. Zilmet in pipe pump is characterized by low noise, no pollution, small volume, space saving, high level of installation, excellent product quality and comprehensive service, which is worthy of customers' choice. ShangHai Longya pump also focuses on the manufacturing of zilmet pipe pump, submersible motor and water supply pipe pump set. Welcome to consult!